5 Steps to Master Reset Your Hoverboard

Picture this: You’re all set to take your hoverboard for a thrilling ride, but suddenly, it starts behaving oddly, making your adventure come to an abrupt halt. Don’t fret! Before you consider a costly repair or replacement, there’s a simple yet effective solution – a master reset. 

To master reset your hoverboard, follow these simple steps. First, ensure your safety and turn off the hoverboard. Look for the reset button or follow the specified reset process in your user manual. Press and hold the reset button for a few seconds until the reset is initiated. Then, perform the calibration process to ensure smooth operation. Finally, test your hoverboard to enjoy a smooth and thrilling riding experience.

At Repair Shack, we believe in empowering hoverboard riders with the knowledge to troubleshoot and resolve minor issues on their own. However, for complex and difficult issues, we are always here to help.

In this comprehensive guide, we’ll take you through five easy steps to master reset your hoverboard and get it back to its smooth, gliding state. So buckle up, and let’s dive into the world of hoverboard resetting!

How to Master Reset Your Hoverboard

Step 1: Safety First

Before attempting any reset or troubleshooting, ensure your safety and the safety of those around you. Turn off the hoverboard and place it on a level surface to prevent accidents. Wearing protective gear like helmets, knee pads, and elbow pads is essential, especially for beginners and youngsters. Safety is paramount, so make sure to observe all precautions and guidelines while handling your hoverboard.

Step 2: Power Down the Hoverboard

To initiate the master reset, power down your hoverboard completely. Locate the power switch and turn it off. If your hoverboard has a remote control, ensure that it is also turned off. Disconnect any charging cables and accessories. This step ensures that the reset process starts from a clean slate, reducing the risk of interference from any external factors.

Step 3: Perform a Hard Reset

Now, it’s time to perform the master reset. Most hoverboards come with a reset button or a specific reset process that varies depending on the brand and model. Refer to your hoverboard’s user manual to find the exact method for your device. In many cases, you may need to press and hold a combination of buttons or perform a sequence of actions to initiate the reset process. The reset button is usually located near the charging port or on the hoverboard’s underside. Once you’ve found the reset button or followed the specified reset process, press and hold it for a few seconds until you see some indication that the reset has been initiated. This could be a series of LED lights flashing or the hoverboard powering off and back on. The hard reset will clear any glitches or software issues that might be causing problems.

Step 4: Calibration

After the hard reset, it’s essential to calibrate your hoverboard to ensure smooth and accurate operation. Calibration helps the hoverboard’s internal sensors accurately gauge your movements and maintain stability while riding. Again, refer to your user manual for the calibration process specific to your hoverboard model. Typically, calibration involves a series of movements or button presses while the hoverboard is turned on. The calibration process may vary slightly among different hoverboards, so following the correct instructions is crucial to achieve optimal results.

Step 5: Test and Enjoy

With the master reset and calibration completed, it’s time to test your hoverboard. Power it on and check if the issues that were plaguing your ride have been resolved. Take a few test rides in a safe and open area to ensure that the hoverboard is functioning smoothly. If everything seems to be in order, you’re all set to enjoy the thrilling and smooth riding experience your hoverboard was designed for!


Master resetting your hoverboard is a simple yet powerful technique to troubleshoot and resolve minor issues without the need for costly repair services. Following these five easy steps ensures that your hoverboard starts afresh and operates optimally, delivering the smooth gliding experience you crave. 

At Repair Shack, we encourage hoverboard riders to take control and perform master resets confidently. However, for more complex issues, our skilled technicians are always here to assist. So remember, the next time your hoverboard acts up, don’t fret! A master reset might be all it takes to unleash the thrills of smooth riding once again!

We hope you find the information helpful. If you would like to book an appointment with one of our expert technicians, feel free to contact us or visit our website for more information. 

Leave a Comment

Your email address will not be published. Required fields are marked *